A5 Series
Machine Setup Parameters (TE-A5, IMC510)
Last Updated: 20. November 2025Clamp Parameter Value Range Description General– Sensor Type– Actuator Type– 1st Step Release Pressure– End Release Pressure– Maximum Sensor Pressure– Minimum Voltage (Sensor)– Maximum Voltage (Sensor) EndatElectric25 bar10 barMachine TON...
Core Pulse
Last Updated: 20. November 2025Smart Sequenzer Settings Pulse High/Low Active On the Page “Machine Settings” you can select if the Puls Signal is High or Low active. This setting if for all Cores with...
Rotary Table Zero-Point Guide
Last Updated: 20. November 2025Applicable Models: VHA, VHL, VHG5 1. Purpose Clarify the zero-point reference and proximity-sensor logic for forward and reverse rotation of rotary tables.This document prevents confusion during service and function testing....
PLAIMMX Weight Control (TE.500.6)
Last Updated: 19. November 2025Page Overview Contents ✅ Enable of the function Status of the function This status message shows the current state of the weight control function, helping the operator understand whether the...
PLAIMMX Anti Flash (TE.500.6)
Last Updated: 19. November 2025Page Overview Contents ✅ Enable of the function With this checkbox, the option can be disabled. When the option is disabled, no flash forces are calculated during the injection process,...
PLAIMMX Anti Flash V1.0 (UF.510)
Last Updated: 19. November 2025Page Overview Contents ✅ Enable of the function With this checkbox, the option can be disabled. When the option is disabled, no flash forces are calculated during the injection process,...
PLAIMMX Weight Control V1.0 (UF.510)
Last Updated: 19. November 2025Page Overview Contents ✅ Enable of the function Status of the function This status message shows the current state of the weight control function, helping the operator understand whether the...
Synchronized Heating
Last Updated: 19. November 2025Available from version: UF.510.1Reference: monday.com report Overview Starting with version UF.510.1, a new Synchronized Heating feature is available for barrel and internal hotrunner heating. The goal is to bring all...
Lubrication (Greasing)
Last Updated: 19. November 2025Option Selection on Fixdata This page allows the user to configure lubrication (greasing) settings for different parts of the machine. There are six different greasing zones available, and each zone...
[IMC400]Dynamic Hardware Configuration Manual
Last Updated: 19. November 20251. Screen Click Dynamic Hardware Configuration on the maintenance page. 2. Configuration 3. Adding Cards (Manual Setting) Example:Default Card + AT6402 + DI9371 + DO9322 + DO8332 + AI4632 4....
Option: Degasing (03A303)
Last Updated: 19. November 2025The Degassing Function is typically used after injection to remove residual gas, moisture, or to enable foaming inside the mold. This function is implemented in the Smart Sequencer under the...
Option: HotWater Unit (06A746)
Last Updated: 19. November 2025This function is used to interface with an additional Hot Water Unit (mold temperature control unit).At the moment, this option is implemented only for injection B 1. Machine Option 2....
Option: Cavity Pressure Sensor (07A441)
Last Updated: 19. November 20251. Machine Option 2. User Settings (Injection / Cavity Pressure Settings page) 2.1 Cavity Pressure Settings 2.1.1 Cavity Pressure Settings 1 2.1.2 General Information 2.2 Switchover condition settings To use...
Option: Spring Mold (DLA5)
Last Updated: 19. November 2025In DL models, when the mold closing process is performed using two pumps, an issue can occur after the mold is closed and the system attempts to close the halfnut....
Machine Setup Parameters (TE-A5, IMC510)
Last Updated: 19. November 2025Clamp Parameter Value Range Description General– Sensor Type– Actuator Type– 1st Step Release Pressure– End Release Pressure– Maximum Sensor Pressure– Minimum Voltage (Sensor)– Maximum Voltage (Sensor) EndatElectric25 bar10 barMachine TON...